Filaform Adhesive Spray Extra Strength
For the prints that fight back.
High-warp materials. Tall parts on tiny footprints. Overnight jobs you can’t babysit. Extra Strength holds them all down, and still lets go once the bed cools.
5.0/5
An eight-hour print that warps at hour six is a day gone. Three seconds of spray is cheap insurance.
- Extra
- hold for high-warp materials and small footprints
- 100 ml
- per bottle
- ~30 °C
- self-release as the bed cools
- 150+
- sprays per bottle
Sound familiar?
Every first-layer failure, handled.
One bottle turns the least reliable step in 3D printing into the most boring one, and every print you don't reprint is filament and hours back in your pocket.
High-warp materials
ABS and friends peel off the bed the moment you stop watching. Big flat parts rarely survive to the last layer.
A stronger hold, formulated specifically for the materials that fight hardest.
Tiny footprints
Tall parts standing on a few square millimetres shear off mid-print and take the whole job with them.
Extra grip on whatever contact area the part gives you, even when it’s barely any.
The blob of death
A part that lets go overnight clumps molten filament around the nozzle until it swallows the hotend, tearing out thermistors and wiring, with repairs running into hundreds of dollars.
Keep the part anchored and the blob never gets its start: the cheapest hotend protection there is.
Failed overnight jobs
An eight-hour print that fails at hour six is a whole day gone, and filament, power and queue time with it.
Three seconds of spray before you walk away. Cheap insurance for the jobs you can’t babysit.
Perfect bottom layers
Glue sticks, roll-on and paint-on adhesives clump and layer up, so the bottom of every print inherits the lumps instead of the plate’s finish.
Goes on thin and evenly, perfectly transferring your build plate’s texture into the print, whether smooth, textured or patterned.
Stronger grip, stuck parts?
More hold usually means chiselling the part off afterwards and gouging the plate.
Not here: the same ~30 °C self-release as Standard. Parts come off clean when the bed cools.
- 100+ printers
- Developed across hundreds of prints on more than a hundred machines before it went in a bottle.
- Smooth & textured PEI
- Tested on both plate finishes. It works very well on either surface.
- Tuned for years in Melbourne
- Made and bottled in Australia, with a formulation refined over several years of printing.
Two formulas
Which spray do I need?
Standard
The everyday workhorse.
Pick it if: Most of your printing is general-purpose parts on common materials.
Works with
- PLA
- PLA+
- PETG
- ABS
- Nylon
Extra Strength
This pageFor the prints that fight back.
Pick it if: You print high-warp materials, or tall parts with very little bed contact, and everything else has let go.
Works with
- PLA
- PLA+
- PETG
- ABS
- Nylon
Both formulations: not recommended for ASA on smooth build plates, as adhesion can become excessive.
Reviews
Don't take our word for it.
It just works… really really well
“This stuff just works, spray it on, excellent adhesion, no lifting but prints are still easy to remove - to top it off it's really easy to clean the print surface and it won't leave a horrible residue. I'll never print without this stuff.”
Verified customer · May 2023
Rated 5.0/5 across 3 customer reviews on 3dprintergear.com.au
How to use
Four steps. Three seconds of work.
Clean
Wash the build plate with warm soapy water and let it dry.
Spray
One even coat across the build area, from 15–20 cm away. Let it dry for a few minutes.
Print
The first layer stays put for the whole job.
Release
As the plate cools to about 30 °C, the part lets go on its own. Between jobs, just re-spray the patch under the last part.
Certified Australian Made
Made in Australia. The sticker proves it.
Filaform Adhesive Spray is made and bottled in Melbourne, and certified by the Australian Made Campaign. It's the only product in our range entitled to carry the green-and-gold kangaroo. When we put the sticker on something, it's earned.
Printing everyday materials?
The Standard formula covers PLA, PLA+, PETG, ABS and nylon with the same clean self-release.